Amada Emk ManualManual. Amada ARIES 222 224 Programming Manual NC Turret Punch Press. Amada AMADAN 04PC Operator Manual. Amada Manuals User Guides - CNC Manual Acces PDF Amada Emk Manual Amada Emk Manual 7025 Firestone Boulevard. Buena Park, CA 90621. (714) 739-2111. FAX (714) 670-8020. www.amada.com Page 5/25. Amada ARIES 245 Programming Manual NC Turret Punch Press. Amada AE NT Series Programming Manual CNC Turret Punch Press. Amada EM NT Series Operator Manual CNC Turret Punch Press. Amada Vipros 357 Queen with 18PC Programming Limits. Amada Vipros lll Z K 3610 NT with AMNC-F Pre-installation Guide.
AMADA AE NT Series CNC Turret Punch Press G-Codes and M-Codes for cnc machinists who work on Amada AE255NT / AE2510NT CNC turret punch presses.
Amada Emk Programming Manual Instructions
Contents Gta v pc cracked download.
G Codes AMADA CNC Turret Punch Press
G Code | Description |
---|---|
G00 | Linear interpolation cancel |
G01 | Linear interpolation start |
G04 | Dwell |
G06 | Designation of worksheet thickness and material |
G20/G21 | Inch/metric select function |
G25 | Auto-repositioning |
G27 | Auto-repositioning |
G26 | Bolt hole circle [BHC] |
G28 | Line at angle [LAA] |
G29 | Arc [ARC] |
G36 | Grid-X [GRD-X] |
G37 | Grid-Y [GRD-Y] |
G50 | Home retract |
G66 | Shear proof [SHP] |
G67 | Square [SQR] |
G68 | Nibbling arc [NBL-A] |
G69 | Nibbling line [NBL-L] |
G70 | Punch off (No punching) |
G72 | Pattern origin |
G73 | Symmetry (option) |
G78 | Punching arc [PNC-A] |
G79 | Punching line [PNC-L] |
G90 | Absolute programming |
G91 | Incremental programming |
G92 | Establishing coordinate system |
G93 | Offset-1 [OFS-1] |
G94 | Offset-2 [OFS-2] |
M Codes AMADA CNC Turret Punch Press
Contents Gta v pc cracked download.
G Codes AMADA CNC Turret Punch Press
G Code | Description |
---|---|
G00 | Linear interpolation cancel |
G01 | Linear interpolation start |
G04 | Dwell |
G06 | Designation of worksheet thickness and material |
G20/G21 | Inch/metric select function |
G25 | Auto-repositioning |
G27 | Auto-repositioning |
G26 | Bolt hole circle [BHC] |
G28 | Line at angle [LAA] |
G29 | Arc [ARC] |
G36 | Grid-X [GRD-X] |
G37 | Grid-Y [GRD-Y] |
G50 | Home retract |
G66 | Shear proof [SHP] |
G67 | Square [SQR] |
G68 | Nibbling arc [NBL-A] |
G69 | Nibbling line [NBL-L] |
G70 | Punch off (No punching) |
G72 | Pattern origin |
G73 | Symmetry (option) |
G78 | Punching arc [PNC-A] |
G79 | Punching line [PNC-L] |
G90 | Absolute programming |
G91 | Incremental programming |
G92 | Establishing coordinate system |
G93 | Offset-1 [OFS-1] |
G94 | Offset-2 [OFS-2] |
M Codes AMADA CNC Turret Punch Press
Amada Emk Programming Manual User
M Code | Function |
---|---|
M00 | Program stop |
M01 | Optional stop |
M02 | Program end |
M08 | Beginning of punching completion signal delay |
M09 | End of punching completion signal delay |
M10 | Work hold and unclamp |
M11 | Work hold and release |
M12 | Nibbling pattern |
M13 | Press mode cancel |
M30 | End of tape |
M31 | Rear workholder and cassette cylinder lower |
M32 | Side table bearings lower |
M33 | Loading command |
M34 | Unloading command |
M35 | Job search end |
M36 | Unloading preparation command |
M37 | Penultimate worksheet signal |
M38 | Job end signal |
M39 | Total job end signal |
M80 | Workchute open |
M81 | Workchute close |
M96 | Subprogram recall command |
M97 | Subprogram end command |
M120 | Mild mode on |
M121 | Mild mode cancel |
M500 | Punching pattern (punch without shear angle) |
M501 | Punching pattern (punch with shear angle) |
M502 to M505 M570 to M575 | Knockout pattern |
M506 to M509 | Slitting pattern |
M510 to M559 M800 to M999 | Forming pattern |
M560 to M569 | Marking pattern |
M681 to M683 | Punching speed |
M686 | Punching speed command cancel |
M687 | Standby position compensation cancel (for forming patterns) |
M690 | Press air blow |
M691 | Press air blow cancel |
M692 | Press raise |
M693 | Press raise cancel |
M696 | NEX tool punching mode on |
M697 | NEX tool punching mode cancel |